Woodpecker LED D Curing Light Unit

Features: Wireless Three working modes:- Full, Ramping, Pulse. Time setting:- 5s, 10s, 15s, 20s, 25s, 30s, 35s, 40s. A full charge can be used for over 400 times. (10s/time) Constant light intensity, the solidification effect is not affected by the consumption of remaining power. With wire or wireless. It can run directly on commercial power supply if the battery runs out.
Key Specifications: Rechargeable Lithium battery: ICR18490, 3.7V, 1400mAh Adapter: Input - AC100V-240V 50Hz/60Hz, Output - DC5.0V/1A Wavelength: 420nm-480nm Light intensity: 1000mW/cm²~1700mW/cm² Environment temperature: +5°C~+40°C Relative humidity: 30%~75% Atmosphere pressure: 70kPa to 106kPa
Packaging: 1 x curing light unit 1 x stand 1 x light protector 1 x charger 1 x optic probe 1 x instruction manual For Woodpecker LED.D Light Probe: Click here to buy the Light Cure Probe
Direction to Use: Start by fully charging the device. Recharge the battery for at least 4 hours before the first-time usage. Familiarize yourself with the basic operation techniques and read the instruction manual carefully. Ensure that you have a general knowledge of dental restoration, dental treatment, and dental whitening. Install the components of the LED.D curing light as follows: Take off the red cap from the optical fiber and insert the metal part into the front of the main unit, securely screwing the fiber to the end. Fix the light hood on the bottom of the optical fiber. Set the working mode by pressing the mode button on the device. The corresponding indicator will turn on to indicate the selected mode. There are three working modes available: Full power mode: In this mode, the blue light radiates at full power. Ramping mode: The blue light power gradually increases and reaches its highest power 5 seconds later. Pulse mode: The blue light works in a pulsating pattern. Set the solidifying time by pressing the time button on the device. You can choose from 8 different working times: 5, 10, 15, 20, 25, 30, 35, or 40 seconds. If you select 5 seconds, the blue light will shine at a higher intensity (1500mW/cm² to 1700mW/cm²). If you select 10, 15, 20, 25, 30, 35, or 40 seconds, the blue light will shine at a slightly lower intensity (1000mW/cm² to 1200mW/cm²). To start or stop emitting the blue light, aim the optical fiber at the desired position and press the power button on the device. During the operation, you can stop the blue light at any time by pressing the power button. The LED.D curing light is equipped with a battery detect circuit. If low power is detected, the indicator on the device will blink, indicating the need for charging. Please charge the device promptly to ensure uninterrupted usage. After use, clean the optical fiber with a calico to remove any remaining resin and maintain its effectiveness. The LED.D curing light will automatically turn off if no action occurs within 2 minutes. You can turn it back on by pressing any button. Please note that the LED.D curing light emits a high-intensity blue light, so avoid direct irradiation to the eyes. Take precautions to protect the patient's eyes and wear appropriate eye protection when necessary.
Additional Info: Country of Origin: PRC Manufacturer: Woodpecker
Warranty: Manufacturer/Importer warranty of 5 year Warranty (from the date of invoice) on PCB (Power Circuit Board) and 12 months warranty is applicable on all the parts of the product excluding physical damage as applicable for this product. Service and Warranty are handled by the manufacturer/importer directly for this product Teethment will not be liable to replace the Products and the liability to replace any such Product is that of the Manufacturer/Importer Teethment and the Buyer acknowledge that the Products purchased/usedare a subject matter of original Manufacturer/Importer’s warranties only Any or all claims in relation to returns and replacement shall be made to the concerned Manufacturer/Importer only and Teethment may assist the customer in registering a request to get the Product replaced or serviced. The Buyer acknowledges that the Products once sold will not be exchanged or taken back unless the seal of the package or the Product is intact or not altered in any manner or is not tampered as the case may be.